Toyota Yaris: G16e-gts (lubrication) / Oil Pump

Toyota Yaris XP210 (2020-2025) Reapir and Service Manual / Engine & Hybrid System / G16e-gts (lubrication) / Oil Pump

Installation

INSTALLATION PROCEDURE 1. INSTALL OIL PRESSURE AND TEMPERATURE SENSOR (a) Apply adhesive to 2 or 3 threads of the oil pressure and temperature sensor...

Components

COMPONENTS ILLUSTRATION *1 FAN AND GENERATOR V BELT *2 ENGINE WIRE *3 NO. 2 AIR HOSE *4 ENGINE UNDER COVER RH *5 NO. 1 AIR TUBE *6 COMPRESSOR ASSEMBLY WITH PULLEY *7 NO...

Other information:

Toyota Yaris XP210 (2020-2025) Reapir and Service Manual: Inspection


INSPECTION PROCEDURE 1. INSPECT WINDSHIELD WIPER SWITCH ASSEMBLY (a) Check the resistance. (1) Measure the resistance according to the value(s) in the table below. Standard Resistance: Front Wiper Switch Tester Connection Condition Specified Condition z5-14 (MIST) -z5-5 (E) MIST position Below 1 Ω z5-14 (MIST) -z5-5 (E) Except MIST position 10 kΩ or higher z5-10 (W_OFF) - z5-5 (E) OFF position Below 1 Ω z5-10 (W_OFF) - z5-5 (E) Except OFF position 10 kΩ or higher z5-13 (+S) - z5-5 (E) AUTO position Below 1 Ω z5-13 (+S) - z5-5 (E) Except AUTO position 10 kΩ or higher z5-11 (+1) - z5-5 (E) LO position Below 1 Ω z5-11 (+1) - z5-5 (E) Except LO position 10 kΩ or higher z5-12 (+2) - z5-5 (E) HI position Below 1 Ω z5-12 (+2) - z5-5 (E) Except HI position 10 kΩ or higher Front Washer Switch Tester Connection Condition Specified Condition z5-15 (WF) - z5-5 (E) ON position Below 1 Ω z5-15 (WF) - z5-5 (E) OFF position 10 kΩ or higher Auto Sensitivity Adjustment Switch Tester Connection Condition Specified Condition z5-4 (VR) - z5-5 (E) P1 position 1102 to 1218 Ω z5-4 (VR) - z5-5 (E) P2 position 570 to 630 Ω z5-4 (VR) - z5-5 (E) P3 position 256...

Toyota Yaris XP210 (2020-2025) Reapir and Service Manual: Removal


REMOVAL CAUTION / NOTICE / HINT The necessary procedures (adjustment, calibration, initialization, or registration) that must be performed after parts are removed and installed, or replaced during camshaft removal/installation are shown below. Necessary Procedure After Parts Removed/Installed/Replaced Replaced Part or Performed Procedure Necessary Procedure Effect/Inoperative Function when Necessary Procedure not Performed Link Camshaft (for intake or exhaust camshaft) Camshaft timing gear assembly Camshaft timing exhaust gear assembly Engine coolant temperature sensor Spark plug Inspection After Repair Poor idle, etc...

Categories

Break-In Period

No special break-in is necessary, but a few precautions in the first 600 miles (1,000 km) may add to the performance, economy, and life of the vehicle.

Do not race the engine. Do not maintain one constant speed, either slow or fast, for a long period of time. Do not drive constantly at full-throttle or high engine rpm for extended periods of time. Avoid unnecessary hard stops. Avoid full-throttle starts.

read more

 
Copyright © 2025 www.toyaris4.com