Toyota Yaris: Rear Seat Outer Belt Assembly / Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH side and LH side.
- The procedure listed below is for the LH side.
PROCEDURE
1. INSTALL REAR SEAT OUTER BELT ASSEMBLY
(a) Inspect the rear seat outer belt assembly.
Click here
| (b) Engage the guides to temporarily install the rear outer belt assembly. |
|
(c) Temporarily install the 2 bolts.
(d) Tighten bolt (A) and then bolt (B).
Torque:
Bolt (A) :
12.5 N·m {127 kgf·cm, 9 ft·lbf}
Bolt (B) :
42 N·m {428 kgf·cm, 31 ft·lbf}
| (e) Install the shoulder anchor of the rear seat outer belt assembly with the bolt. Torque: 42 N·m {428 kgf·cm, 31 ft·lbf} |
|
(f) Connect the floor anchor of the rear seat outer belt assembly with the bolt.
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
NOTICE:
Do not allow the floor anchor of the rear seat outer belt assembly to overlap the protruding parts of the vehicle body.
 | Protruding Part |
| (g) Check that the ELR locks. NOTICE: This check should be performed with the rear seat outer belt assembly installed to the vehicle. (1) With the rear seat outer belt assembly installed to the vehicle, check that the belt locks when it is pulled out quickly. |
|
(h) Remove the bolt to disconnect the floor anchor of the rear seat outer belt assembly.
2. INSTALL INNER ROOF SIDE GARNISH
Click here
3. CONNECT REAR SEAT OUTER BELT ASSEMBLY
(a) Connect the floor anchor of the rear seat outer belt assembly with the bolt.
Torque:
42 N·m {428 kgf·cm, 31 ft·lbf}
NOTICE:
Do not allow the floor anchor of the rear seat outer belt assembly to overlap the protruding parts of the vehicle body.
 | Protruding Part |
4. INSTALL DECK TRIM SIDE PANEL ASSEMBLY
Click here
5. INSTALL QUARTER TRIM PANEL ASSEMBLY
Click here
6. CONNECT FRONT SEAT OUTER BELT ASSEMBLY
Click here
7. INSTALL LAP BELT OUTER ANCHOR COVER
Click here
8. INSTALL FRONT DOOR SCUFF PLATE
Click here
9. INSTALL DECK TRIM REAR COVER
Click here
10. INSTALL DECK FLOOR BOX LH
Click here
11. INSTALL DECK FLOOR BOX RH
Click here
12. INSTALL DECK BOARD ASSEMBLY
Click here
13. INSTALL PACKAGE TRAY TRIM PANEL ASSEMBLY (w/ Package Tray Trim)
Click here
14. INSTALL REAR SEAT CUSHION LOCK HOOK
Click here
15. INSTALL BENCH TYPE REAR SEAT CUSHION ASSEMBLY
Click here
16. INSTALL REAR SEATBACK ASSEMBLY
Click here
Inspection
INSPECTION PROCEDURE 1. INSPECT REAR SEAT OUTER BELT ASSEMBLY (a) Before installing the rear seat outer belt assembly, check the ELR function. NOTICE: Do not disassemble the retractor...
Other information:
Toyota Yaris XP210 (2020-2024) Reapir and Service Manual: Problem Symptoms Table
PROBLEM SYMPTOMS TABLE HINT: Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table...
Toyota Yaris XP210 (2020-2024) Reapir and Service Manual: Ecu Configuration
ECU CONFIGURATION STABILIZE A POWER SOURCE ON THE VEHICLE SIDE Shut off as many following systems and parts as possible since they would generate an electrical load. CAUTION: If vehicle systems affect a voltage to reduce during reprogramming, it may disable the ECU in reprogramming, which concludes an ECU replacement...
Categories
- Manuals Home
- Toyota Yaris Owners Manual
- Toyota Yaris Service Manual
- Engine & Hybrid System
- How to connect USB port/Auxiliary jack
- Auto Lock/Unlock Function
- New on site
- Most important about car
Front Seat Belt Pretensioners
The front seat belt pretensioners are designed to deploy in moderate or severe frontal, near frontal collisions.
In addition, the pretensioners operate when a side collision or a rollover accident is detected. The pretensioners operate differently depending on what types of air bags are equipped. For more details about the seat belt pretensioner operation, refer to the SRS Air Bag Deployment Criteria.
