Toyota Yaris: Wiper And Washer System / Data List / Active Test

Toyota Yaris XP210 (2020-2024) Reapir and Service Manual / Vehicle Exterior / Wiper / Washer / Wiper And Washer System / Data List / Active Test

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

HINT:

Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

(a) Read the Data List according to the display on the GTS.

Body Electrical > Main Body > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Wiper Motor Cam Switch 1	Windshield wiper motor cam signal	OFF or ON	OFF: Front wiper motor stop ON: Front wiper motor operation	-
Wiper Control Switch HI	Front wiper switch HI position signal	OFF or ON	OFF: Front wiper switch not in HI position ON: Front wiper switch in HI position	-
Communication Wiper ECU	Connection status between windshield wiper motor assembly and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Not Connected OK: Connected	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Communication Wiper Module	Connection status between windshield wiper relay assembly and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Not Connected OK: Connected	DTCs are stored if a malfunction occurs in the CXPI communication system.
Communication Humidity/Rain Sensor	Connection status between rain sensor and main body ECU (multiplex network body ECU)	STOP or OK	STOP: Not Connected OK: Connected	Although this item is displayed on the GTS, it is not applicable to this vehicle.
R Wiper Stop Function at Back Door/Trunk Lid Open	Function to enable the back door open linked rear wiper suspend function	Enable or Disable	Customize setting displayed	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Rear Wiper Washer Function	Function to enable the rear washer linked rear wiper operation function	Enable or Disable	Customize setting displayed	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Rear Wiper with Reverse Setting	Function to enable the R shift position linked rear wiper operation function	Disable, 1 time, Continuation	Customize setting displayed	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Wiper Power Relay	Wiper relay position signal	OFF or ON	OFF: WIPER relay off ON: WIPER relay on	-
Front Washer Relay	Front washer operation	OFF or ON	OFF: Front washer switch off ON: Front washer switch ON	-
Front Wiper Lo Operation	Windshield wiper motor assembly LO operation	OFF or ON	OFF: Front wiper motor stopped ON: During front wiper motor LO operation	-
Front Wiper Hi Operation	Windshield wiper motor assembly HI operation	OFF or ON	OFF: Front wiper motor stopped ON: During front wiper motor HI operation	-
Rear Washer Relay	Rear washer operation	OFF or ON	OFF: Rear washer switch off ON: Rear washer switch ON	Although this item is displayed on the GTS, it is not applicable to this vehicle.

Chassis > Steering Angle Sensor > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Wiper OFF Switch	Front wiper switch OFF position signal	OFF or ON	OFF: Front wiper switch not in OFF position ON: Front wiper switch in OFF position	-
Wiper Auto/Int Switch	Front wiper switch or INT position signal	OFF or ON	OFF: Front wiper switch not in or INT position ON: Front wiper switch in INT position	-
Wiper Lo Switch	Front wiper switch LO position signal	OFF or ON	OFF: Front wiper switch not in LO position ON: Front wiper switch in LO position	-
Wiper Hi Switch	Front wiper switch HI position signal	OFF or ON	OFF: Front wiper switch not in HI position ON: Front wiper switch in HI position	-
Wiper Mist Switch	Front wiper switch MIST position signal	OFF or ON	OFF: Front wiper switch not in MIST position ON: Front wiper switch in MIST position	-
Washer Switch	Washer switch Fr WASH position signal	OFF or ON	OFF: Washer switch not in Fr WASH position ON: Washer switch in Fr WASH position	-
Rear Wiper INT Switch	Rear wiper switch Rr INT position signal	OFF or ON	OFF: Rear wiper switch not in Rr INT position ON: Rear wiper switch in Rr INT position	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Rear Wiper ON Switch	Rear wiper switch Rr ON position signal	OFF or ON	OFF: Rear wiper switch not in Rr ON position ON: Rear wiper switch in Rr ON position	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Rear Washer Switch	Washer switch Rr WASH position signal	OFF or ON	OFF: Washer switch not in Rr WASH position ON: Washer switch in Rr WASH position	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Intermittent Time Volume (Shortest)	Intermittent time adjustment switch condition	OFF or ON	OFF: Washer switch not in P4 position ON: Washer switch in P4 position	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Intermittent Time Volume (Shorter)	Intermittent time adjustment switch condition	OFF or ON	OFF: Washer switch not in P3 position ON: Washer switch in P3 position	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Intermittent Time Volume (Longer)	Intermittent time adjustment switch condition	OFF or ON	OFF: Washer switch not in P2 position ON: Washer switch in P2 position	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Intermittent Time Volume (Longest)	Intermittent time adjustment switch condition	OFF or ON	OFF: Washer switch not in P1 position ON: Washer switch in P1 position	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Wiper Spec Info	Function information	Unknown, Auto spec or Int spec	Unknown: Specification not stored Auto spec: w/ Auto wiper system Int spec: w/o Auto wiper system	-

Body Electrical > Rain and/or Humidity Sensor > Data List

Tester Display	Measurement Item	Range	Normal Condition	Diagnostic Note
Sensor Info	Rain sensor temperature circuit condition	OK or NG	OK: Rain sensor is normal NG: Malfunction in rain sensor thermistor	-
Sensor Reaction Info	Rain sensor output condition	OK or NG	OK: Rain sensor is normal NG: Malfunction in rain sensor thermistor output	-
Sensor High Temp Info	Rain sensor high temperature condition	OK or NG	OK: Rain sensor is normal NG: Rain sensor temperature is high	-
Sensor Low Temp Info	Rain sensor low temperature condition	OK or NG	OK: Rain sensor is normal NG: Rain sensor temperature is low	-
Wiper Switch Auto Signal	Windshield wiper switch assembly (AUTO position) condition	OFF or ON	OFF: Windshield wiper switch assembly not in AUTO position ON: Windshield wiper switch assembly in AUTO position	-
Intermittent Time Volume	Auto sensitivity adjustment switch condition	Shortest, Shorter, Longer or Longest	Shortest: P4 Shorter: P3 Longer: P2 Longest: P1	*1
Wiper Type	Displays vehicle wiper type	Normal, Reversing (1 Motor) or Reversing (2 Motor)	Shows vehicle wiper type	-
Wiper Stop Position	Windshield wiper motor assembly stop position	Store Area, Lower Rev Pos, Wipe Area or Upper Rev Pos	Store Area/Lower Rev Pos: Lower reverse position or lower Wipe Area: Between lower reverse position and upper reverse position Upper Rev Pos: Upper reverse position	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Wiper Stop Position (Sub Motor)	No. 2 Windshield wiper motor assembly stop position	Store Area, Lower Rev Pos, Wipe Area or Upper Rev Pos	Store Area/Lower Rev Pos: Lower reverse position or lower Wipe Area: Between lower reverse position and upper reverse position Upper Rev Pos: Upper reverse position	Although this item is displayed on the GTS, it is not applicable to this vehicle.
Motor Status	Wiper motor control condition in response to rain sensor request	Normal, Normal (Link Ctrl), Normal (Req Deny), Abnormal or Normal (Wiper Ctrl)	Current motor control condition	-
Wiping Mode Signal (Sensor to Wiper)	Status of command request signal for front wiper speed and intermittent time from rain sensor	Stop, LO Mode, HI Mode, Wait, INT Mode1 (Vehicle Stop), INT Mode2 (Vehicle Stop), INT Mode3 (Vehicle Stop), INT Mode4 (Vehicle Stop), INT Mode5 (Vehicle Stop), INT Mode6 (Vehicle Stop), INT Mode7 (Vehicle Stop), INT Mode1 (Vehicle Run), INT Mode2 (Vehicle Run), INT Mode3 (Vehicle Run), INT Mode4 (Vehicle Run), INT Mode5 (Vehicle Run), INT Mode6 (Vehicle Run), INT Mode7 (Vehicle Run), INT Mode (Sensor Abnormal), OFF (Customize) or Fail Stop	Stop: Windshield wiper switch assembly in AUTO position and stop requested (Windshield wiper switch assembly OFF included) (rain not detected) LO Mode: Windshield wiper switch assembly in AUTO position and LO operation requested HI Mode: Windshield wiper switch assembly in AUTO position and HI operation requested INT Mode 1 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 32.7 s INT Mode 2 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.5 s INT Mode 3 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 9.7 s INT Mode 4 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.4 s INT Mode 5 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.1 s INT Mode 6 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.6 s INT Mode 7 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.8 s INT Mode 1 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.9 s INT Mode 2 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 10.1 s INT Mode 3 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.9 s INT Mode 4 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.5 s INT Mode 5 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 2.1 s INT Mode 6 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.2 s INT Mode 7 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.6 s INT Mode (Sensor Abnormal): Windshield wiper switch assembly in AUTO position and speed sensing intermittent operation requested OFF (Customize): Windshield wiper switch assembly in AUTO position and stop requested (for customization) Fail Stop: Windshield wiper switch assembly in AUTO position and stop requested (sensor malfunction)	-
Wiper LO Single Operation Signal	Wiper LO Single Operation Signal	ON or OFF	ON: Windshield wiper switch assembly in AUTO position and sensor determines small amount of rain while wiper is in stopped position OFF: Windshield wiper switch assembly in AUTO position and wiper in position other than stopped	-
Wiping Mode Signal (Wiper to Sensor)	Response status of command request signal for front wiper speed and intermittent time from rain sensor to windshield wiper relay assembly	Stop, LO Mode, HI Mode, Wait, INT Mode1 (Vehicle Stop), INT Mode2 (Vehicle Stop), INT Mode3 (Vehicle Stop), INT Mode4 (Vehicle Stop), INT Mode5 (Vehicle Stop), INT Mode6 (Vehicle Stop), INT Mode7 (Vehicle Stop), INT Mode1 (Vehicle Run), INT Mode2 (Vehicle Run), INT Mode3 (Vehicle Run), INT Mode4 (Vehicle Run), INT Mode5 (Vehicle Run), INT Mode6 (Vehicle Run), INT Mode7 (Vehicle Run), INT Mode (Sensor Abnormal), OFF (Customize) or Fail Stop	Stop: Windshield wiper switch assembly in AUTO position and stop requested (Windshield wiper switch assembly OFF included) (rain not detected) LO Mode: Windshield wiper switch assembly in AUTO position and LO operation requested HI Mode: Windshield wiper switch assembly in AUTO position and HI operation requested INT Mode 1 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 32.7 s INT Mode 2 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.5 s INT Mode 3 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 9.7 s INT Mode 4 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.4 s INT Mode 5 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.1 s INT Mode 6 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.6 s INT Mode 7 (Vehicle Stop): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.8 s INT Mode 1 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 17.9 s INT Mode 2 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 10.1 s INT Mode 3 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 5.9 s INT Mode 4 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 3.5 s INT Mode 5 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 2.1 s INT Mode 6 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 1.2 s INT Mode 7 (Vehicle Run): Windshield wiper switch assembly in AUTO position and intermittent operation requested of 0.6 s INT Mode (Sensor Abnormal): Windshield wiper switch assembly in AUTO position and speed sensing intermittent operation requested OFF (Customize): Windshield wiper switch assembly in AUTO position and stop requested (for customization) Fail Stop: Windshield wiper switch assembly in AUTO position and stop requested (sensor malfunction)	-
Sensor High Temp History	History of if the rain sensor temperature being high (approximately 80°C (176°F))	OFF or ON	OFF: The rain sensor temperature has not been (approximately 80°C (176°F)) ON: The rain sensor temperature reached high (approximately 80°C (176°F))	Clearing the DTCs also clears the history
Sensor Low Temp History	History of if the rain sensor temperature being low (approximately -40 °C (-104°F))	OFF or ON	OFF: The rain sensor temperature has not been low (approximately -40°C (-104°F)) ON: The rain sensor temperature reached low (approximately -40°C (-104°F))	Clearing the DTCs also clears the history
Vehicle Speed	Vehicle speed	Min.: 0 km/h (0 mph), Max.: 255 km/h (158 mph)	Almost the same as actual vehicle speed	-
Auto Wiper	Setting to switch control between automatic wipers/vehicle speed sensing intermittent time adjustment	Avail or Not Avl	Almost the same as actual vehicle speed	-
Number of Trouble Code	Number of DTCs	0 to 255	Number of stored DTCs displayed	-

*1: Refer to Inspection for each position of the switch.
Click here

ACTIVE TEST

HINT:

Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.

(a) Perform the Active Test according to the display on the GTS.

Body Electrical > Main Body > Active Test

Tester Display	Measurement Item	Control Range	Diagnostic Note
Wiper Power Relay	Function to operate the WIPER relay	OFF or ON	-
Front Washer Relay	Function to operate the windshield washer motor and pump assembly (Front)	OFF or ON	-
Front Wiper Lo Operation	Function to operate the windshield wiper motor assembly in LO	OFF or ON	-
Front Wiper Hi Operation	Function to operate the windshield wiper motor assembly in HI	OFF or ON	-
Rear Washer Relay	Function to operate the windshield washer motor and pump assembly (Rear)	OFF or ON	Although this item is displayed on the GTS, it is not applicable to this vehicle.

Dtc Check / Clear

D..

Diagnostic Trouble Code Chart

D..

Other information:

Toyota Yaris XP210 (2020-2024) Reapir and Service Manual: Recirculated/Fresh Air Modes Switch without User Input

DESCRIPTION If recirculation/fresh mode changes unintentionally and without permission, the following causes are possible. Symptom Factor Recirculation/fresh mode changes without permission Recirculation/fresh mode light blinks Customize setting Change in ambient air temperature Decrease in refrigerant pressure Air conditioner pressure sensor circuit malfunction Engine coolant temperature (high) PROCEDURE 1...

Toyota Yaris XP210 (2020-2024) Reapir and Service Manual: Components

COMPONENTS ILLUSTRATION *1 FRONT NO. 1 VENTILATOR SEAL *2 WATER GUARD PLATE RH *3 OUTER COWL TOP PANEL SUB-ASSEMBLY - - N*m (kgf*cm, ft.*lbf): Specified torque - - ILLUSTRATION *1 BRAKE MASTER CYLINDER O-RING *2 BRAKE MASTER CYLINDER SUB-ASSEMBLY *3 CONNECTOR *4 NO...