Toyota Yaris: Stop And Start System / Stop and Start Priority Control System
DESCRIPTION
In stop and start control status, there is normal status (Standard) and stop and start priority status (Extended).
Stop and start control status can be switched to the desired mode by pressing and holding the stop and start system cancel switch (combination switch assembly), or by operating the steering pad switch assembly, and the mode change is also shown on the multi-information display screen.
When the mode has been switched by pressing and holding the stop and start system cancel switch (combination switch assembly), a signal is sent directly from the stop and start system cancel switch (combination switch assembly) to the engine stop and start ECU.
When the steering pad switch assembly is used to select a control mode, a status change request signal is sent from the combination meter assembly to the engine stop and start ECU via CAN communication.
Cooperative control is performed by the air conditioning amplifier assembly and engine stop and start ECU based on the selected control mode.
When stop and start priority control (Extended) is selected, the operation time of stop and start control will be extended in order to improve fuel economy.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
-
Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.
Click here
-
After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.
Click here
HINT:
- When stop and start priority control (Extended) is selected, the operation of the air conditioning system is limited. If the customer reports that the cooling effectiveness of the air conditioning system is poor, check the selected control mode. If stop and start priority control (Extended) is selected, cancel the control mode and check if the cooling effectiveness of the air conditioning system improves. If it improves, explain to the customer that the operation of the air conditioning system was limited by stop and start control.
- Depending on the vehicle conditions, the stop and start operation time may not change even if stop and start priority control (Extended) is selected.
-
For wire harness and connector inspection procedures and precautions, refer to "
"
PROCEDURE
| 1. | CHECK PROBLEM SYMPTOMS |
(a) Check the problem symptoms.
HINT:
- Check each symptom by checking the suspected areas in the table below.
-
By using the GTS and entering the following menus, the selected mode can be confirmed.
Powertrain / Stop and Start / Data List / Stop & Start A/C Mode
| Problem Symptoms | Trouble Area | Proceed to |
|---|---|---|
| Multi-information display screen does not change after pressing steering pad switch assembly |
| A |
| Multi-information display screen changes without pressing steering pad switch assembly |
| B |
| The status change interrupt display in the combination meter assembly is not displayed, but control changes | Combination meter assembly | C |
| The status change interrupt display in the combination meter assembly is displayed, but control does not change |
| D |
| Control mode returns to default mode after turning ignition switch to ON | Engine stop and start ECU | E |
| B |
 | GO TO STEP 4 |
| C |
 | GO TO METER / GAUGE SYSTEM |
| D |
 | GO TO STEP 7 |
| E |
 | GO TO STEP 8 |
|
| 2. | CHECK OPERATION |
(a) Using the steering pad switch assembly, check that all functions other than "Stop & Start Settings" can be selected.
| Result | Proceed to |
|---|---|
| Only "Stop & Start Settings" cannot be selected | A |
| No function can be selected using the steering pad switch assembly | B |
| B |
 | GO TO STEP 4 |
|
| 3. | CHECK DTC OUTPUT |
(a) Perform a road test.
(b) Read the DTCs.
Powertrain > Stop and Start > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| CAN DTCs are output | B |
| A |
 | REPLACE ENGINE STOP AND START ECU |
| B |
 | GO TO CAN COMMUNICATION SYSTEM |
| 4. | CHECK HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY) |
(a) Disconnect the H60 spiral cable sub-assembly connector.
(b) Disconnect the H6 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
| Tester Connection | Condition | Specified Condition |
|---|---|---|
| H60-11 (+DP) - H6-32 (MSM+) | Always | Below 1 Ω |
| H60-10 (+DP2) - H6-15(MSTI) | Always | Below 1 Ω |
| H60-4 (EAU) - Body ground | Always | Below 1 Ω |
| H60-11 (+DP) - Body ground and other terminals | Always | 10 kΩ or higher |
| H6-32 (MSM+) - Body ground and other terminals | Always | 10 kΩ or higher |
| H60-10 (+DP2) - Body ground and other terminals | Always | 10 kΩ or higher |
| H6-15 (MSTI) - Body ground and other terminals | Always | 10 kΩ or higher |
| NG |
 | REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
| 5. | INSPECT SPIRAL CABLE SUB-ASSEMBLY |
Click here
| NG |
 | REPLACE SPIRAL CABLE SUB-ASSEMBLY |
|
| 6. | INSPECT STEERING PAD SWITCH ASSEMBLY |
Click here
| OK |
 | GO TO METER / GAUGE SYSTEM |
| NG |
 | REPLACE STEERING PAD SWITCH ASSEMBLY |
| 7. | CHECK DTC OUTPUT |
(a) Perform a road test.
(b) Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
(c) Read the DTCs.
Powertrain > Stop and Start > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| CAN DTCs are output | B |
| A |
 | REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
| B |
 | GO TO CAN COMMUNICATION SYSTEM |
| 8. | CHECK DTC OUTPUT |
(a) Perform a road test.
(b) Enter the following menus: Powertrain / Stop and Start / Trouble Codes.
(c) Read the DTCs.
Powertrain > Stop and Start > Trouble Codes| Result | Proceed to |
|---|---|
| DTCs are not output | A |
| DTCs are output | B |
| A |
 | REPLACE ENGINE STOP AND START ECU |
| B |
 | GO TO DIAGNOSTIC TROUBLE CODE CHART |
Engine Hood Courtesy Switch Circuit
DESCRIPTION The engine stop and start ECU detects whether the engine hood is open or closed based on a signal received from the engine hood courtesy switch built into the hood lock assembly...
Backup Boost Converter Circuit
DESCRIPTION A backup boost converter is built into the engine stop and start ECU. The backup boost converter helps maintain the power source voltage when the engine is restarted by stop and start control...
Other information:
Toyota Yaris XP210 (2020-2024) Reapir and Service Manual: Parts Location
PARTS LOCATION ILLUSTRATION *1 BRAKE ACTUATOR ASSEMBLY - SKID CONTROL ECU *2 ECM *3 TEMPERATURE SENSOR *4 AWD LINEAR SOLENOID (TRANSMISSION COUPLING ASSEMBLY) *5 AWD ECU ASSEMBLY - - ILLUSTRATION *1 COMBINATION METER ASSEMBLY - AWD WARNING (MULTI-INFORMATION DISPLAY) *2 AWD CONTROL SWITCH (NO...
Toyota Yaris XP210 (2020-2024) Reapir and Service Manual: Left Front Wheel Speed Sensor Signal Stuck Low (C050023)
DESCRIPTION Refer to DTC C05001F. Click here DTC No. Detection Item DTC Detection Condition Trouble Area DTC Output from C050023 Left Front Wheel Speed Sensor Signal Stuck Low Any of the following is detected: When the +BS terminal voltage is 17...
Categories
- Manuals Home
- Toyota Yaris Owners Manual
- Toyota Yaris Service Manual
- To Set Speed
- G16e-gts (engine Mechanical)
- Opening and Closing the Liftgate/Trunk Lid
- New on site
- Most important about car
Supplemental Restraint System (SRS) Precautions
The front and side supplemental restraint systems (SRS) include different types of air bags. Please verify the different types of air bags which are equipped on your vehicle by locating the “SRS AIRBAG” location indicators. These indicators are visible in the area where the air bags are installed.
The air bags are installed in the following locations:
The steering wheel hub (driver air bag) The front passenger dashboard (front passenger air bag) The outboard sides of the front seatbacks (side air bags) The front and rear window pillars, and the roof edge along both sides (curtain air bags)